Log for 090108a Observer: Riccardo Giovanelli System Configuration: a2010_az360_2009.conf CIMA version 3.1.02 2008-12-29 17:19 "Smart" File: /share/pserverf.sda2/wappdata/wapp.20090108.a2010.****.fits **** LST fits Scan calscan Source Pattern Start coords. ang time loop calmode 0733 0001 90080003 90080004 drift11p2 fixAZdr 072300+024036 19 600 99 loopend radar's back; Bm6B ok 0743 0002 90080005 90080006 power levels ok; quicklook on file 1 ok - step in Dec to 024041... 0756 0004 90080008 90080010 restarting; see below 0745LST 0806 0005 90080010 90080011 0820 0007 90080013 90080014 restarting; see below 0815LST 0830 0008 90080015 90080016 0840 0009 90080017 90080018 0850 0010 90080019 90080020 0900 0011 90080021 90080022 0910 0012 90080023 90080024 0920 0013 90080025 90080026 0930 0014 90080027 90080028 0940 0015 90080029 90080030 0951 0016 90080031 90080032 1001 0017 90080033 90080034 1011 0018 90080035 90080036 1021 0019 90080037 90080038 1031 0020 90080039 90080040 1041 0021 90080041 90080042 1051 0022 90080043 90080044 1101 0023 90080045 90080046 1111 0024 90080047 90080048 1122 0025 90080049 90080050 1132 0026 90080051 90080052 power levels ok 1142 0027 90080053 90080054 1152 0028 90080055 90080056 1202 0029 90080057 90080058 1212 0030 90080059 90080060 1222 0031 90080061 90080062 1232 0032 90080063 90080064 1242 0033 90080065 90080066 1253 0034 90080067 90080068 1303 0035 90080069 90080070 1313 0036 90080071 90080072 1323 0037 90080073 90080074 1333 0038 90080075 90080076 1343 0039 90080077 90080078 1353 0040 90080079 90080080 1403 0041 90080081 90080082 1413 0042 90080083 90080084 1424 0043 90080085 90080086 END LST 1434 Notes: - Upon logging on CIMA, an error message appeared, indicating system was unable to access /share/obs4/usr/a2010 - Any other function after that (e.g. enabling ALFA) cima was "unable" to perform. Exited and reloaded CIMA 3 times, the third after killing -9 CIMA and exiting from observer2 - it worked Possible explanation is that previous observer did not get off cima on time... No time to run TOGS calibration. - Another CIMA quirk: it completed the first 600 sec drift and 1 sec cal without wwriting a fits file (scans 900800001 and 900800002) - produced fits file after scan 00003. -0745LST Dec jumps 5" in CIMA Observation status window... -0755LST: alfadatawin stops updating; killed process and restarted - same (segmentation fault). Power levels on ALFAobswin being updated and looking ok... keeps happening several times, then stabilizes... -0815LST Dec jumps again... Running the new version of CIMA 3.1.02 "Smart"; all ok TOGS run at end only FAA radar on again Beam 6B looks ok Went an extra half hour of NYA time at the end, but note: after sunrise